https://www.drcmachinery.ru/wp-content/uploads/WeChat_20241104140450.mp4

1.Temperature To keep the machining accuracy of the machine within the standard range, it is necessary to ensure that the constant temperature is between 17-25°C and the temperature difference from the ground to the highest point of the machine is kept within ±2°C! Humidity Continuous: 75% or less (non-condensing) Short time: 95% or less (non-condensing) Altitude Below 1000m Installation Conditions To ensure high precision and performance of the equipment, the foundation should be made in strict accordance with the foundation map provided by the seller (refer to the foundation map for specific production requirements) The installation location of the equipment should be away from direct sunlight, sources of vibration (stamping equipment, automobile and railways, etc.) and heat sources (furnaces, heaters, radiation, etc.), away from high-frequency generators, welding machines, etc., to avoid machine production failure or loss of machine precision. Air source requirements Air supply pressure ≥ 0.6 MPa, and the filtration accuracy is 100 microns. Although the machine is equipped with an air filter, the source of compressed air should be as free from moisture as possible. To ensure the normal operation of the equipment, if the compressed air of the air source does not meet the requirements of the air source, it is recommended to add another set of air source purification device (drying, oil removal, filtration) before taking out the machine. Water content in the air source will cause damage to precision components such as spindles and grid scales (component damage caused by this reason is not covered by the warranty), which must be strictly controlled! Power supply 3-phase 380V±10%; 50H Z If the voltage in the area of ​​use is unstable, the machine must be equipped with a stable power supply to ensure the normal operation of the machine. Power requirements Power supply power 55 kVA Recommended power wire diameter: 25 mm2. Switching capacity: 160A   Grounding Good grounding is required, each machine is recommended to be grounded separately, the grounding wire is copper wire, the diameter of the wire should not be less than 10 square mm, and the grounding resistance is less than 4 ohms

This machine is a bridge machining center with a portal (portal-bridge) structure. It has high rigidity of the base frame, symmetrical structure and excellent stability. The design adopts international advanced dynamic stiffness concepts, optimizes moving parts, and adds servo drives on the A and C axes. The machine spindle has a high rotation speed and excellent response speed, which enables high-precision five-axis continuous machining. The machine is intended for use in various industries, such as automotive, mold making, metalworking and other areas of mechanical engineering. The general layout of the machine is made according to the scheme of a bridge portal with a movable beam and fixed racks. The columns are rigidly fixed, the work table is installed permanently on the foundation. The cross member (beam) is fixed to the columns and moves along the X axis. The slide moves along the cross member along the Y axis, and the spindle head moves along the slide along the Z axis.

1, high rigidity, long-term preservation of precision 1.1, the main components of the machine: base, table, column, beam, slider, plunger are used in high-quality resin sand modeling, high strength quality cast iron, with ideal heat treatment process to eliminate residual stress, and the arrangement of sufficient reinforcement plate, to ensure that the whole machine has sufficient strength, rigidity and high stability. 1.2 The XY axis is equipped with heavy-duty roller guides, which have high rigidity and good dynamic precision. 1.3 The three axes drive adopts Taiwan brand large diameter double nut ball screws with compact structure, smooth movement and high precision. The screw support adopts precision screw support bearings, and both ends are pre-stretched to eliminate the loss of precision caused by thermal elongation.

This machine is a bridge machining center with a gantry structure. It has high rigidity base frame, symmetrical design and excellent stability. The design uses advanced international concepts of dynamic rigidity, optimized moving parts, and added servos on the A and C axes. The machine spindle is characterized by high rotation speed and fast response dynamics, which allows high-precision five-axis synchronous processing. The machine is suitable for various fields of mechanical engineering, including automotive, mold production, metal products and other areas of high-precision machining. The general layout of the machine is made according to the scheme of a bridge portal with a movable beam and fixed racks. The columns are rigidly fixed, the work table is installed permanently on the foundation. The cross beam is mounted on the columns and moves along the X axis. The slide moves along the cross beam along the Y axis. The headstock (plunger) moves along the slide along the Z axis.

This machine is a bridge structure with a portal frame. It has high rigidity of the basic structure, symmetrical structure and excellent stability. The machine adopts international advanced concepts of dynamic rigidity, optimized moving parts, and added servo drives on the A and C axes. The main spindle features high rotation speed and fast response, which enables five-axis synchronous machining. The machine is suitable for various fields of machining: automotive, mold making, aerospace, defense, metalworking, etc.

Model GMF4019T Options Unit of measurement Table size 4000X1600 mm Door width 1900 mm Table load 12 T T-slot width 9-22×160 mm Processing range X-axis stroke 4000 mm Y-axis stroke 1900 mm Z-axis stroke 900 mm Distance from spindle end to table 150-1050mm Spindle Taper Bore Type BT50 Nozzle Specification P50T-1-MAS403(45°) X-Axis Rapid Stroke 10m/min Y-Axis Rapid Stroke 12m/min Z-Axis Rapid Stroke 10m/min System Configuration FANUC Oi MF 1 package Motor Configuration X-Axis Motor α iF40

This machine is a portal-type bridge structure with a movable beam and fixed posts. It has a high rigidity base frame, symmetrical design and excellent stability. The machine uses an advanced international design concept taking into account dynamic rigidity, and also optimizes the design of moving parts, adding A/C servos. The machine spindle has high rotation speed and good fast response characteristics, which allows five-axis processing. The equipment is suitable for various machining fields, including automotive, mold making, metal products and other industries. The general layout of the machine is a bridge portal frame with a movable beam: the racks are rigidly fixed to the frame, which is made as a single unit with the work table; the beam is mounted on the posts and moves along the X axis, the slide moves along the beam in the direction of the Y axis, and the caliper moves along the slide in the direction of the Z axis.

GMF3015B Double Column CNC Gantry Machining Center for Heavy Cutting PURPOSE:  Based on the inherited advantages of traditional gantry machines such as high rigidity, symmetrical structure and high stability, this machine introduces the international concept of advanced dynamic rigid structure and optimizes the design of moving parts. The machine has large torque and good quick response characteristics, and is suitable for the needs of various processing fields such as automobiles, molds, aerospace, military and equipment.